On newsstands
now!

Preview Issue

Web Extras

Subscribe Now

Access Current Digital Issue (subscribers only)

Woodwork

Winter 2012-2013

Preview this issue

Buy This Issue

Buy Back Issues

Local Guides

All Guides
Alabama
Alaska
Arizona
Arkansas
California
Colorado
Connecticut
DC
Delaware
Florida
Georgia
Hawaii
Idaho
Illinois
Indiana
Iowa
Kansas
Kentucky
Louisiana
Maine
Maryland
Massachusetts
Michigan
Minnesota
Mississippi
Missouri
Montana
Nebraska
Nevada
New Hampshire
New Jersey
New Mexico
New York
North Carolina
North Dakota
Ohio
Oklahoma
Oregon
Pennsylvania
Rhode Island
South Carolina
South Dakota
Tennessee
Texas
Utah
Vermont
Virginia
Washington
West Virginia
Wisconsin
Wyoming

Woodworking Shop

1 | 2 | 3 | 4 | 5 | Next

Triangle Sandpaper
by American Woodworker Editors Wednesday, June 19, 2013
Triangle Sandpaper Triangular hook-and-loop sandpaper for detail sanders first loses it’s bite at the end because that part does most of the work. By cutting a used piece, as shown, and shifting it forward on the pad, you can obtain a fresh end...
Portable Shaving Horse
by American Woodworker Editors Wednesday, June 19, 2013
Portable Shaving Horse Bring your shop to the woods. In the modern workshop, the tablesaw is the central tool. A few centuries ago, for coopers (barrel makers), bodgers (chairmakers), and carpenters, the shaving horse was indispensable. Woodworkers use...
Q & A: Lock Miter Joint
by American Woodworker Editors Wednesday, June 12, 2013
Q & A: Lock Miter Joint Q: How do you set up a lock miter bit? A: There are two critical adjustments (Fig. A). First, you set the bit’s height; second, you position the fence. Once that’s done, you can rout both sides of a lock miter joint...
Laser Cutting Guide
by American Woodworker Editors Tuesday, June 11, 2013
Laser Cutting Guide I use a laser pen to improve accuracy when making miter cuts on a compound miter saw. It’s especially helpful when cutting ornate or rabbeted moldings. First I mark the edge of the molding where it is to be cut. Then I lay a...
Router Scarfing Jig
by American Woodworker Editors Tuesday, June 11, 2013
Router Scarfing Jig Boatbuilders often need to join boards end to end to make longer planks. Instead of a butt joint they make a long taper on each board and overlap the ends. This is called a scarf joint. One or two scarf joints are easily planed by...
Taping Diagonals
by American Woodworker Editors Tuesday, June 11, 2013
Taping Diagonals Measuring diagonals with a tape was a pain for me because the hook would always fall off the corner before I could get a reading. Finally I adapted a tape by riveting a small, notched block to the end, as shown. Now I can slip the tape...
Q & A: Easy Drawer Dividers
by American Woodworker Editors Wednesday, June 5, 2013
Q & A: Easy Drawer Dividers Q: Help! The junk drawer in our kitchen is out of control! I have trouble finding anything in there. Is there a simple way to add dividers to my kitchen drawers without taking them apart? A: You bet! Here’s a way...
Storing Lumber
by American Woodworker Editors Tuesday, June 4, 2013
Storing Lumber This rack is easily made from galvanized iron pipe and threaded floor flanges. For light loads use 10-in. lengths of 1/2-in. pipe and 2x4s. For heavier loads go to 3/4-in. pipe and 4x4s. Be sure to anchor the flanges securely to the wall...
Saw Sharpening Jig
by American Woodworker Editors Tuesday, June 4, 2013
Saw Sharpening Jig I made this jig to hold a dovetail or other backsaw when filing and resetting the teeth. To use, insert the saw blade, teeth up, and clamp the jig in a bench vice.
Multiple Plugs
by American Woodworker Editors Tuesday, June 4, 2013
Multiple Plugs Faced with cutting hundreds of plugs for a big project, I came up with this idea: I cut the plugs a little deeper than needed. Then I ran strips of masking tape down the faces of the plugs. When I cut them free on the bandsaw they stayed...
Q & A: Clean Up Squeeze Out
by American Woodworker Editors Tuesday, May 28, 2013
Q & A: Clean Up Squeeze Out Q: I saw one of those woodworking wizards on television the other day. As I watched the guy build a three-day project in 30 minutes, I noticed he washed off glue squeeze out with a wet cloth immediately after clamping....
Q & A: Sanding Scratches Revealed
by American Woodworker Editors Monday, May 20, 2013
Q & A: Sanding Scratches Revealed Q: What can I do to see sanding scratches before I apply stain? I always miss some of them until it’s too late. A: Doesn’t that drive you crazy? Just when you should be home free, wham! Now you’re...
Q & A: Salvaging a Rusty Plane Iron
by American Woodworker Editors Wednesday, May 15, 2013
Q & A: Salvaging a Rusty Plane Iron Q: I’ve got an old plane that my grandfather left me. I’d like to use it, but its cutting iron is really rusty. Do I need to buy a new one? A: Don’t throw away that iron yet. Flattening the back...
Q & A: The Right Mortise/Tenon Fit
by American Woodworker Editors Monday, May 6, 2013
Q & A: The Right Mortise/Tenon Fit Q: What’s the right fit between a mortise and a tenon? I’m going crazy trying to measure them with a dial caliper! A: You’re not alone. This question has bugged just about every woodworker, but...
Snap-On Soft Jaws
by American Woodworker Editors Friday, May 3, 2013
Snap-On Soft Jaws I’ve been using an old metal-working vise in my shop for years. Occasionally I really do need a metal-working vise, but most often I use it to hold drawer sides up high when cutting dovetails. Unfortunately the metal jaws can be...

Sort By

Syndication

On newsstands now!

Woodwork

Winter 2012-2013

Woodworking Shop

On newsstands
now!