|
Even though they’re sexy, benchtop mortising machines aren’t the only power-tool option when it comes to cutting square-shouldered mortises. A drill-press mortising attachment can be just as effective and it costs a lot less: $30 to $80 instead of $200 or more. I’ll show you how to tune any out-of–the-box mortising attachment so it’s easy to install and a joy to use.
Mortising attachments are available for almost every drill press. Although they vary in appearance, they all have three basic components: a fence, a chisel holder and a hold-down. Upgrading these parts to stabilize the workpiece and operating the drill press at the optimal speed are the keys to success.
I get first-class results with my tuned-up mortising attachment. That means I don’t have to store a large, heavy mortiser that I would only use occasionally. On the drill press, I can slow the speed way down, too, so I don’t overheat my bits. Drill-press mortising is slower, but it’s much more pleasant, a lot quieter and much less nerve-wracking than using a mortiser.
Square mortises require special bits, which can be bought individually or in sets. Bits range in price from $10 to more than $50 apiece. Inexpensive bits usually won’t stay sharp as long (see “Start Sharp, Stay Sharp,” page 74), but dropping one on the concrete floor won’t give you a heart attack, either.
|
|
Two-piece mortising chisels cut square holes. The auger bit fits inside the chisel and protrudes slightly. During operation, the auger drills a round hole and the four-sided chisel squares the corners. Cut side by side, square holes create mortises (see photo, above).
Photo 1: Slow down. Mortising chisels work best at slow speeds, between 1,000 rpm and 1,500 rpm, depending on the mortise size and the wood density. Within this range, use trial and error to find the speed that works best.
Photo 2: Mount the mortising fence on a separate base, rather than fastening it directly to the drill-press table. Then clamp the base to the drill-press table. This setup makes the fence easy to adjust, so positioning the workpiece is a breeze.
Photo 3: Install the chisel and bit. The chisel holder, which clamps on to the quill, centers the chisel directly beneath the chuck. Lock the chisel with its collar tightly against the holder. Then slide the bit into the chuck.
Photo 4: Leave a gap. Position the auger bit with its cutting head about 1/16 in. away from the domed inside surface of the hollow chisel. Don’t jam these two parts together. This gap is essential, because it allows shavings cut by the auger to be lifted into the hollow chisel and ejected. If the gap is too small or too large, the trapped shavings will bind the bit.
Photo 5: Lubricate the auger bit after making sure it spins freely inside the chisel. If the bit squeals when you power up, it isn’t centered precisely. Shut off the power, rotate the chisel 90 (or 180 or 270) degrees and retest. If the squeal persists, loosen the chisel holder and rotate it slightly. Then reposition the chisel.
Photo 6: Check your hold-down. If it doesn’t sit flat on the workpiece, grind or file it until it does. A poorly fitting hold-down won’t hold the workpiece firmly enough against the base. While you’re mortising, any workpiece movement can bind the bit in the mortise and wreck your setup—or the bit.
Photo 7: Clamp a fence in front of the workpiece to hold it firmly against the fence assembly. Together with the hold-down, this fence captures the workpiece effectively during operation, eliminating any movement. When you reposition the workpiece between cuts, this fence keeps it correctly aligned.
Photo 8: Stiffen the table with a brace. On many drill presses, mortising exerts enough downward pressure to flex the table. Like workpiece movement, any table movement will cause trouble. If the table flexes, the chisel will bind in the mortise. A two-part adjustable brace is much easier to install.
Photo 9: Square the chisel. For the mortise shoulders to be parallel, the chisel must be perpendicular to the fence. Loosen the chisel, rotate it flush against the squarely cut end of your workpiece and retighten.
Photo 10: Set the depth of the cut. The top of the chisel’s arch indicates the bottom of the square mortise.
Photo 11: Position the workpiece for mortising. First, clamp the base and fence assembly so the center point of the auger bit is on the centerline of the mortise. Then slide the workpiece between the fences until the outer edge of the hollow chisel aligns with the mortise end line.
Photo 12: Establish the ends of the mortise first. Then clear out the middle. Always engage all four sides of the chisel or two opposite sides. Apply steady pressure and advance the cut slowly. Don’t push too hard. Match your feed rate to the cutting action of the auger by watching the flow of chips exiting the chisel. Easy—but firmly—does it.
|